[MLB-WIRELESS] Need HELP please!!!
Mikel Pretty
mpretty at sunitafe.edu.au
Wed May 7 12:32:59 EST 2003
Having trouble configuring a 2 x cisco 350 PCMCIA cards. I am using Redhat
9.0 on both machines (Machines have identical hardware in them) and am
trying to get the machines to talk to each other via wireless each machine
is configured identically except for the mac addresses and ip's obviously.
I am using a compaq PCI cradle but that is not the issue as this cradle
worked fine with my other Cisco 340 PCMCIA card in RedHat 7.3. The cradle
detects the card and beeps ect running ifconfig and iwconfig it shows the
cards present.
I have Eth0 as a Intel 100mbps card
I have Eth1 as Cisco 350 Wireless pcmcia (in Compaq cradle)
This is what get on each machine when I run iwconfig
eth1 IEEE 802.11-DS ESSID:"test" Nickname:"alby"
Mode:Ad-Hoc Frequency:2.412GHz Cell: BA:00:E1:00:28:02
Bit Rate:11Mb/s Tx-Power=20 dBm Sensitivity=0/65535
Retry limit:16 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:176/10 Signal level:-110 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:111 Missed beacon:0
wifi0 IEEE 802.11-DS ESSID:"test" Nickname:"alby"
Mode:Ad-Hoc Frequency:2.412GHz Cell: BA:00:E1:00:28:02
Bit Rate:11Mb/s Tx-Power=20 dBm Sensitivity=0/65535
Retry limit:16 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:176/10 Signal level:-110 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:111 Missed beacon:0
This is what get on each machine when I run lsmod
Module Size Used by Not tainted
nls_iso8859-1 3516 0 (autoclean)
nls_cp437 5116 0 (autoclean)
vfat 13004 0 (autoclean)
fat 38808 0 (autoclean) [vfat]
parport_pc 19076 1 (autoclean)
lp 8996 0 (autoclean)
parport 37056 1 (autoclean) [parport_pc lp]
autofs 13268 0 (autoclean) (unused)
airo_cs 4900 0 (unused)
airo 49608 1 [airo_cs]
ds 8680 1 [airo_cs]
yenta_socket 13472 1
pcmcia_core 57216 0 [airo_cs ds yenta_socket]
e100 60644 1
keybdev 2944 0 (unused)
mousedev 5492 0 (unused)
hid 22148 0 (unused)
input 5856 0 [keybdev mousedev hid]
usb-uhci 26348 0 (unused)
usbcore 78784 1 [hid usb-uhci]
ext3 70784 2
jbd 51892 2 [ext3]
This is the setup of ifcfg-eth0 on both machines (yes each machine has diff
ip just cant be fagged putting seperate ones in for each machine)
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=static
IPADDR=10.12.0.1
NETMASK=255.255.255.0
GATEWAY=192.168.1.1
This is the setup of ifcfg-eth1 on both machines (yes each machine has diff
ip just cant be fagged putting seperate ones in for each machine)
DEVICE=eth1
ONBOOT=yes
TYPE=wireless
BOOTPROTO=static
IPADDR=192.168.10.2
NETMASK=255.255.255.0
ESSID=test
MODE=Ad-Hoc
HWADDR=00:0c:30:d4:b0:f4
RATE=auto
CHANNEL=11
With each machine set up the same I can not get them to ping etc. I hope
someone can help as I have started to run out of ideas.
Thanks
Mikel
*******************************************************************************
This footnote confirms this email has been checked for the presence of viruses
however our liability is limited to the resupply of attachments only.
Any representations or opinions expressed are those of the individual sender,
and not necessarily those of Sunraysia Institute of TAFE.
*******************************************************************************
To unsubscribe: send mail to majordomo at wireless.org.au
with "unsubscribe melbwireless" in the body of the message
More information about the Melbwireless
mailing list