[MLB-WIRELESS] Linux Router problems.

[Brenton D]

Yep, i would have said enable ip forwarding.
--- owner-melbwireless at wireless.org.au
<d_ashburner at hotmail.com> wrote:
> Hi Mark,
> You have IP forwarding enabled?
> What about routes for the different segments ?
> 
>
http://www.melbournewireless.org.au/wiki/?RoutingHowTo
> 
> do a dump of your routing table and post it.
> what happens when you traceroute from machines on
the different segments? if 
> their default routs are not pointing to your (new)
router then they may not 
> be sending data the way you think it is
> 
> cheers,
> dna
> 
> >From: Mark Aitken <vk3jma at wia.org.au>
> >Reply-To: vk3jma at wia.org.au
> >To: melbwireless at wireless.org.au
> >Subject: [MLB-WIRELESS] Linux Router problems.
> >Date: Wed, 02 Mar 2005 16:25:30 +1100
> >
> >Hi People,
> >
> >Well I have gone and built up a small router out of
an old 200Mhz Pent. 
> >computer.
> >
> >It has 4 ethernet cards (1 x PCI and 3 x ISA)
> >
> >Here is the "ifconfig" capture....
> >
> >
> >eth0      Link encap:Ethernet  HWaddr
00:40:05:58:62:2B          inet 
> >addr:192.168.0.1  Bcast:192.168.0.255 
Mask:255.255.255.0
> >          UP BROADCAST RUNNING MULTICAST  MTU:1500 
Metric:1
> >          RX packets:0 errors:0 dropped:0
overruns:0 frame:0
> >          TX packets:0 errors:21 dropped:0
overruns:0 carrier:42
> >          collisions:357 txqueuelen:100
> >          Interrupt:12 Base address:0xe000
> >
> >eth1      Link encap:Ethernet  HWaddr
00:C0:6C:55:93:50          inet 
> >addr:10.10.145.210  Bcast:10.10.145.255 
Mask:255.255.255.0
> >          UP BROADCAST RUNNING MULTICAST  MTU:1500 
Metric:1
> >          RX packets:0 errors:0 dropped:0
overruns:0 frame:0
> >          TX packets:21 errors:0 dropped:0
overruns:0 carrier:0
> >          collisions:0 txqueuelen:100
> >          Interrupt:10 Base address:0x300
> >
> >eth2      Link encap:Ethernet  HWaddr
00:C0:6C:57:67:90          inet 
> >addr:10.1.1.5  Bcast:10.1.1.255  Mask:255.255.255.0
> >          UP BROADCAST RUNNING MULTICAST  MTU:1500 
Metric:1
> >          RX packets:0 errors:0 dropped:0
overruns:0 frame:0
> >          TX packets:0 errors:1 dropped:0
overruns:0 carrier:0
> >          collisions:0 txqueuelen:100
> >          Interrupt:11 Base address:0x320
> >
> >eth3      Link encap:Ethernet  HWaddr
00:C0:6C:54:28:15          inet 
> >addr:192.168.1.1  Bcast:192.168.1.255 
Mask:255.255.255.0
> >          UP BROADCAST RUNNING MULTICAST  MTU:1500 
Metric:1
> >          RX packets:0 errors:0 dropped:0
overruns:0 frame:0
> >          TX packets:21 errors:0 dropped:0
overruns:0 carrier:0
> >          collisions:0 txqueuelen:100
> >          Interrupt:5 Base address:0x340
> >
> >lo        Link encap:Local Loopback          inet
addr:127.0.0.1  
> >Mask:255.0.0.0
> >          UP LOOPBACK RUNNING  MTU:3924  Metric:1
> >          RX packets:0 errors:0 dropped:0
overruns:0 frame:0
> >          TX packets:0 errors:0 dropped:0
overruns:0 carrier:0
> >          collisions:0 txqueuelen:0
> >
> >
> >Now eth0 and 1 work ak.  I can ping other hosts on
my lan from each port 
> >with no problems but
> >eth2 (my adsl side of the lan) is not pingable (ie
the modem 10.1.1.1) nor 
> >this machine (10.1.1.4)
> >
> >I notice from LINUXCONF that the entry for eth1 has
all IO and IRQ values 
> >for all ISA cards
> >(which are all the same type ETHER 16, NE2000
compt.) on its entry.
> >
> >Can some one assist so as I can move to the nest
phase, that is, 
=== Message Truncated === 


=====
Brenton (iViLe)
Access node fut from the web, live stats. http://211.28.235.187:6111
ivile01 at yahoo.com.au ivile at bur.st
www.ivile.tk
www.waveguides.tk
MW NODE: FUT, FUU


	
		
__________________________________ 
Celebrate Yahoo!'s 10th Birthday! 
Yahoo! Netrospective: 100 Moments of the Web 
http://birthday.yahoo.com/netrospective/

To unsubscribe: send mail to majordomo at wireless.org.au
with "unsubscribe melbwireless" in the body of the message