[MLB-WIRELESS] GDW -> GHO

[Ryan]

How do u guys pin piont excacly were to piont to? from places far away? we
are only 3.19km away
----- Original Message -----
From: "Ben Holko" <Ben.Holko at GlobalCenter.net.au>
To: "Richard Van Orsouw" <Richard.Van.Orsouw at optus.com.au>;
<melbwireless at wireless.org.au>
Sent: Tuesday, June 10, 2003 2:27 PM
Subject: RE: [MLB-WIRELESS] GDW -> GHO


> UDP is transport also
>
> IP is layer 3
>
>
>
> -----Original Message-----
> From: owner-melbwireless at wireless.org.au
> [mailto:owner-melbwireless at wireless.org.au]On Behalf Of Richard Van
> Orsouw
> Sent: Tuesday, June 10, 2003 1:58 PM
> To: 'melbwireless at wireless.org.au'
> Subject: RE: [MLB-WIRELESS] GDW -> GHO
>
>
> 51.9km's to be exact!!,
> thanx Jamie, I will try austwireless, but failing that I will give u a
call.
>
> btw, wrt the OSI model, my link seems to be working upto Layer 3, Layer 4
(
> Transport, tcp ) is having issues, since picophone works fine (udp) to
prove
> this, can someone on GHO  run a TFTP server which uses udp so I can use it
> to measure the bandwidth.
>
> Cheers.
>
>
>
> > ----------
> > From: Richard Van Orsouw
> > Sent: Tuesday, 10 June 2003 1:08 PM
> > To: 'melbwireless at wireless.org.au'
> > Subject: RE: [MLB-WIRELESS] GDW -> GHO
> >
> > Too bad you couldn't send me a veritech on wednesday's order to
melbourne
> > :)
> >
> >
> > > ----------
> > > From: Jamie Moir
> > > Sent: Tuesday, 10 June 2003 10:35 AM
> > > Cc: 'melbwireless at wireless.org.au'
> > > Subject: Re: [MLB-WIRELESS] GDW -> GHO
> > >
> > >
> > > On Tue, 10 Jun 2003, Richard Van Orsouw wrote:
> > >
> > > > I am either going to replace the entrasys card with a veritech 200mW
> > or
> > > I
> > > > have a Cisco AP1200 which I might run in client AP mode. Does any
know
> > > where
> > > > I can get a pigtail for it, I believe it uses a RF-TNC ?
> > >
> > > I have reverse gender TNC pigtails for $27 if you dont get a local
> > source.
> > >
> > > > was also suggested trying mtu/ttl values. This problem I am
> > experiencing
> > > is
> > > > most likely due to the poor rx from gdw to gho, but it also could be
a
> > > > timing issue due to the long round trip delays ( since my link is
64km
> > > plus
> > > > another 20km to the other nodes). Any suggestions on values I could
> > try
> > > > would be appreciated.
> > >
> > > 64km is really an impressive link, I think Perth is largely too flat
for
> > > that =)
> > >
> > > Jamie
> > >
> > >
> > > To unsubscribe: send mail to majordomo at wireless.org.au
> > > with "unsubscribe melbwireless" in the body of the message
> > >
> > >
> >
> > To unsubscribe: send mail to majordomo at wireless.org.au
> > with "unsubscribe melbwireless" in the body of the message
> >
> >
>
> To unsubscribe: send mail to majordomo at wireless.org.au
> with "unsubscribe melbwireless" in the body of the message
>
>
>
>
> To unsubscribe: send mail to majordomo at wireless.org.au
> with "unsubscribe melbwireless" in the body of the message
>


To unsubscribe: send mail to majordomo at wireless.org.au
with "unsubscribe melbwireless" in the body of the message