[MLB-WIRELESS] Making a roof mounted antenna easily removable?

[Matthew Hill]

Rik

Umm im a bit busy to ring all councils in victoria...perhaps you could ???
:D

But definitely, when I find my details, ill add them :D

Regards,

Matthew

-----Original Message-----
From: owner-melbwireless at wireless.org.au
[mailto:owner-melbwireless at wireless.org.au]On Behalf Of rik
Sent: Tuesday, 21 January 2003 8:02 PM
To: Melbourne Wireless
Subject: Re: [MLB-WIRELESS] Making a roof mounted antenna easily removable?

well please let the wiki know

http://melbourne.wireless.org.au/wiki/?CouncilRegulations

kingston knox maroondah melbourne and whitehorse are all 5 meters


----- Original Message -----
From: "Matthew Hill" <matthew.hill at matthewhillonline.com>
To: "Melbourne Wireless" <melbwireless at wireless.org.au>
Sent: Tuesday, January 21, 2003 7:38 PM
Subject: RE: [MLB-WIRELESS] Making a roof mounted antenna easily removable?


>
> Rik
>
> Differnet councils have different by laws in regards to antenna heights :D
>
> Cheers
>
> Matthew
> -----Original Message-----
> From: owner-melbwireless at wireless.org.au
> [mailto:owner-melbwireless at wireless.org.au]On Behalf Of rik
> Sent: Tuesday, 21 January 2003 6:40 PM
> To: Justin; melbwireless at wireless.org.au
> Subject: Re: [MLB-WIRELESS] Making a roof mounted antenna easily
removable?
>
> concils max hight is 5 meters not 3
> ----- Original Message -----
> From: "Justin" <littlejuz at optusnet.com.au>
> To: <melbwireless at wireless.org.au>
> Sent: Tuesday, January 21, 2003 6:26 PM
> Subject: [MLB-WIRELESS] Making a roof mounted antenna easily removable?
>
>
> > Hi Folks,
> >
> >  I bought a 5 meter length of 42 mill gal pipe on the weekend to mount
to
> my
> > roof as an antenna. I'm going to stick it through a hole in the tiles
and
> > use 2 U bolts a little over a meter apart to secure the bottom of it to
> the
> > internal roof structure. The bottom of the pole will rest on the top of
a
> > wall frame. I've got a large stick-on rubber flashing to go over the
hole
> in
> > the tiles. The mast will be trimmed to about 4 and a bit meters over all
> to
> > meet the councils '3 meters above the roof' bylaw.
> >
> >  So, the question. How can I make the top of this mast removable so I
can
> > bring it down and put it up every now and then without having to undo
the
> > entire installation? I don't have to ruin / reseal the rubber flashing
> every
> > time and also loosen and tighten the U bolts blah blah blah....
> >
> >  Would cutting it and welding some sort of larger diameter sleeve be ok
so
> I
> > can take off only the section sticking above the tiles? I was also
> thinking
> > cutting a slot or two in the bottom of the sleeve and using another U
bolt
> > to clamp it on.
> >
> >  Any ideas? Comments? Suggestions?
> >
> > Regards,
> > Gaz.
> >
> >
> >
> >
> > To unsubscribe: send mail to majordomo at wireless.org.au
> > with "unsubscribe melbwireless" in the body of the message
> >
>
>
> To unsubscribe: send mail to majordomo at wireless.org.au
> with "unsubscribe melbwireless" in the body of the message
>
>
> To unsubscribe: send mail to majordomo at wireless.org.au
> with "unsubscribe melbwireless" in the body of the message
>


To unsubscribe: send mail to majordomo at wireless.org.au
with "unsubscribe melbwireless" in the body of the message


To unsubscribe: send mail to majordomo at wireless.org.au
with "unsubscribe melbwireless" in the body of the message