[MLB-WIRELESS] Horrible pain...

[Rowan Wainwright-Smith]

I'm with Andrew Dean... don't run the windows update.

There are known faults with "Windows Update", it does not work properly
(well... more like at all :) ).

I have never (in about 3 years) been able to make it work properly.
Just use the clean install and leave it at that.

Rowan

fenn_b at smktech.com.au wrote:

> Hi All,
>
> I am finally conceding (temporary) defeat with a wireless related
> problem I am having. I recently received my beautiful Ricoh PCMCIA->PCI
> bridge as purchased in the bulk buy (thanks Paul!) and popped it in a
> machine with a lucent orinoco silver. To my delight, it worked perfectly
> and all was good in the world.
>
> I then put it in a second machine, which I have a specific application
> for. Unfortunately, there due to it's nature, it must be running windows
> (win 98 to be precise). It too worked perfectly there as well, until I
> decided to install a "Windows Update" (it was a fresh install of 98SE),
> after which the orinoco WOULD NOT WORK no matter what I tried.
>
> I'm by no means a newbie when it comes to the caveats and peculiarities
> of the windows' Plug'n'pray system, but this one has me beat.
>
> Before I get into the major rant, quick system setup summary:
>
> PC
>  - Intel P133
>  - Old Intel Triton FX chipset (concerned about this)
>  - 64MB ram
>  - Win98SE with Orinoco-wrecking-update
>  - Ricoh (RL5C475?) PCMCIA->PCI bridge
>  - Genuine Orinoco Silver (dunno about firmware)
>
> Basically, what happens is that when the machine boots (or I insert the
> card), the drivers all detect and install, the card comes up in the
> cardbus screen, but it makes a low your-card-isn't-working "BEEEP", as
> opposed to the normal Card-OK beep it makes.
>
> Further investigation shows that the orinoco is sharing the I/O address
> with the cardbus adapter (which I thought was OK). I basically stuffed
> around with it for aaaages, until I found that if I changed the I/O
> address of the cardbus adapter (once booted), it would re-allocate
> resources on the spot, the card would come up and it would work
> perfectly. However, as soon as I reboot, the orinoco will jump on to
> whatever resource I have allocated the cardbus adapter and fail to work
> again.
>
> So far I have:
>  - Fooled with IRQ's/IO addresses till the cows come home (they haven't
> yet)
>  - Adjusted PCI IRQ steering settings
>  - Reinstalled orinoco driver completely (it's running the latest)
>  - Reinstalled ricoh driver completely
>  - Found an alternate ricoh driver and tried that
>  - Tried taking out multiple other devices
>  - Tried manually changing I/O or IRQ values via the registry (device
> manager won't let you change it on the orinoco)
>  - Fooled with the EnableIRQSharing key in the orinico hardware registry
> entry
>
> Basically, there seems to be no way that I can find to stop the orinoco
> jumping to the same I/O address as the cardbus adapter, and hence making
> itself completely and utterly useless. In addition to this, the BIOS on
> the motherboard appears to be so old it is pre-flashable and I therefore
> can't do a flash upgrade (I'm 95% sure).
>
> Just wondering whether anyone else has experienced anything similar.
>
> Any suggestions are most welcome (and thanks in advance),
>
>         Fenn.
>
> To unsubscribe: send mail to majordomo at wireless.org.au
> with "unsubscribe melbwireless" in the body of the message



To unsubscribe: send mail to majordomo at wireless.org.au
with "unsubscribe melbwireless" in the body of the message